HCR vs LSR: Choosing Between Compression Moulding and Liquid Silicone Injection

HOME >> BLOG

HCR vs LSR: Choosing Between Compression Moulding and Liquid Silicone Injection

Time:2026-11-14
Read:7

High-consistency rubber (HCR) and liquid silicone rubber (LSR) are the same polymer family processed in two fundamentally different ways, and choosing the wrong one is one of the more expensive mistakes in a silicone programme. The conclusion for buyers: LSR wins on precision, flash and high-volume consistency; HCR wins on tooling cost, part size and low-to-mid volume economics. The crossover usually sits somewhere between 20,000 and 50,000 pieces per year for a small part, but geometry can move it either way.

The two materials in practice

HCR arrives as a gum-like sheet or strip that must be compounded, catalysed and then formed under pressure in a heated mould. It is the traditional route for silicone consumer goods: mats, spatulas, cases, teethers, gaskets. Because the material is stiff before cure, it is placed or injected into an open cavity, and the closing press does the shaping.

LSR arrives as two low-viscosity components that are pumped, metered and mixed at the machine, then injected into a closed, heated cavity where it cures in seconds. Because it flows, it fills fine detail and thin walls, produces almost no flash, and can encapsulate inserts and bond to plastics in the same cycle. The trade-off is equipment: LSR needs a dosing system, a cold-runner or open-nest tool and a press set up for liquid injection, all of which sit in the tooling and setup cost.

Process comparison

FactorHCR compression mouldingLSR injection moulding
Tooling cost, small partLower; simpler steel, no cold runnerHigher; precision steel, cold runner, dosing setup
Unit cost at low volumeBetter, because setup is amortised over fewer partsHigher, driven by setup and material handling
Unit cost at high volumeCycle-time bound; labour for loading and deflashingBetter; short cycles, minimal deflashing
FlashVisible; deflashing or tear-trim neededMinimal to none on well-built tools
Achievable toleranceModerate; parting-line variation mattersTighter, especially on small features
Thin wallsLimited; material will not flow farGood down to roughly 0.3–0.5 mm
Part sizeLarge parts feasible; press size is the limitTypically small to medium; machine capacity limits
Inserts and overmouldingPossible but manual and slowerStrong advantage; encapsulation in one cycle
Typical economic quantityFrom a few hundred to tens of thousandsFrom tens of thousands upward per year

Where the cost crossover actually sits

Buyers often ask for a single quantity threshold, and it does not exist in a useful form. What drives the crossover is the ratio of tooling cost to annual volume, adjusted for the labour content of each process. A part with a lot of hand deflashing in HCR carries a per-unit labour penalty that never goes away; at 30,000 pieces a year that penalty can repay an LSR tool within two seasons. A large, simple part with almost no flash, by contrast, may never justify LSR because the tool would be enormous and the machine availability limited.

A practical way to decide is to request both quotes on the same drawing and the same annual volume, with tooling shown separately. Then compute total cost of ownership over two years: tooling plus unit price times volume, plus the cost of your own incoming inspection for flash and dimensional rejects. The inspection line is where HCR programmes quietly lose money, because badly flashed parts generate sorting work at your warehouse rather than at the factory.

Design implications that change the decision

LSR tolerates undercuts better, fills fine texture, and holds sharp internal corners that HCR would round off under pressure. It also allows wall transitions that HCR cannot fill without trapped air. If your design has a 0.6 mm wall running into a 3 mm boss, that is an LSR design almost regardless of volume.

HCR, on the other hand, is more forgiving of thick sections and large flat areas, and it handles high Shore A compounds more comfortably. Very hard grades, filled compounds and parts with moulded-in fabric or mesh are usually HCR territory. If the part must be produced in a colour-matched, small-batch run for a promotional programme, HCR also lets the factory run a few hundred pieces economically, which LSR setup costs discourage.

Hybrid and adjacent options

There is a middle route worth knowing: HCR transfer or injection moulding, where gum is injected into a closed cavity rather than compressed in an open one. It reduces flash compared with plain compression moulding and shortens cycles, at a tooling cost below full LSR. For parts in the 10,000 to 30,000 range with tight flash requirements, this is frequently the best-value answer, and a supplier who offers all three processes can quote them side by side instead of steering you to whichever press is free.

What to put in the RFQ

  1. Annual volume and order pattern, not just the first order quantity — the process decision depends on the run rate.
  2. Critical dimensions with tolerances, and which of them are functional rather than cosmetic.
  3. Flash acceptance: a written limit, ideally with a photograph of the acceptable parting line.
  4. Any insert, overmould or bonding requirement, since that often settles the choice immediately.
  5. Colour and surface finish expectations, including texture and gloss.
  6. Whether the tool must be transferable, and who owns it.

FAQ

Is LSR material more expensive than HCR?

The raw material is usually dearer per kilogram, but the gap is smaller than the tooling gap. On thin-walled parts, LSR often uses less material per part because there is no flash or sprue to waste, which narrows the difference further.

Can the same tool run both processes?

No. The tool designs are not interchangeable: LSR needs a cold runner and a sealed cavity, HCR needs a different shut-off and venting arrangement. A programme that plans to "start with HCR and move to LSR later" should budget for a second tool.

Which process gives better colour consistency?

LSR, generally, because pigment is metered into a closed system and each shot uses freshly mixed material. HCR colour depends on compound lot mixing and press operators, so batch-to-batch variation is wider and should be covered by an agreed tolerance.

How long does each route take from drawing to first samples?

Both typically run four to six weeks for a straightforward part, with LSR slightly longer at the front end because the dosing setup and cold runner need validation. Complex inserts or multi-cavity tools extend either timeline.

Next step

If you are unsure which process your part belongs in, send the 3D file and annual volume and we will quote both routes with tooling separated, so the comparison is arithmetic rather than opinion. See the process scope on our custom silicone OEM and ODM service page, or review typical parts in silicone 3C and digital accessories and silicone baby products.

Related products