How to Set an AQL Inspection Standard for Silicone and PVC Parts
An AQL standard turns "good quality" into a number that both sides can inspect against. For silicone and PVC parts the useful version is short: three defect classes, one sampling plan, a photographic boundary for cosmetic issues, and a remedy clause. Everything else is detail. Buyers who skip this step do not get better goods — they get the same goods and a longer argument.
Why "zero defects" is not a specification
Zero defects sounds rigorous and is usually unenforceable. It implies 100% inspection of every unit, which nobody performs on a 20,000-piece order, and it treats a 0.1 mm flow mark the same as a tear in a teether. The result is a standard that cannot be applied at the inspection table, so it gets applied by mood.
A workable standard accepts that cosmetic variation exists in moulded rubber, defines how much is acceptable, and reserves zero tolerance for the things that actually matter: safety, regulatory compliance and function.
Classify defects before you count them
| Class | Definition | Silicone / PVC examples | Typical AQL |
|---|---|---|---|
| Critical | Unsafe, illegal, or unusable | Sharp flash on a teether, tear exposing filler, restricted substance failure, wrong material | 0 |
| Major | Function or claim fails | Hardness outside tolerance, suction base will not hold, wall below minimum, colour off the approved master | 1.0–2.5 |
| Minor | Cosmetic only, no effect on use | Flash under 0.2 mm, flow marks on a hidden face, light mottling, isolated dust speck | 2.5–4.0 |
AQL values apply per defect class, per lot. They are not a single number for the whole shipment, and a supplier who quotes one figure for everything has not understood the standard.
Choosing the inspection level and the lots
- Use ISO 2859-1 (or its Chinese equivalent GB/T 2828.1) at general inspection level II for normal consumer goods. Level I is for low-risk bulk, level III for high-value or safety-related items.
- Define the lot. One purchase order line, one colour, one size. Mixing colours into one lot hides a colour-specific problem inside a passing average.
- Treat critical defects separately at AQL 0, which in practice means either 100% inspection of the safety feature or a defined special sampling plan.
- State when inspection happens — during production, pre-shipment, or both. Pre-shipment alone is cheaper; during-production catches a problem while it can still be fixed.
Cosmetic limits need a photographic boundary
"No visible defects" is not a limit. Write numbers and put them on a photo:
- Flash — maximum 0.2 mm on non-grip surfaces, none on sealing edges or bite surfaces.
- Parting line — permitted where it does not cross a grip or contact area; state the maximum step.
- Specks and contamination — maximum count and size per 100 cm², measured on the visible face only.
- Colour — visual match to a signed master under D65 light, or a stated colour difference limit if you have a spectrophotometer.
- Surface — no oil bloom, no tackiness, no blush on translucent parts.
The single most effective document in any silicone order is a signed boundary sample set: one acceptable, one marginal, one reject, kept sealed at the factory and photographed into the PO.
Dimensional and functional checks worth writing in
Do not measure everything. Measure what decides whether the part works:
- Hardness on a durometer, three readings on a flat thick section, compared with the datasheet tolerance.
- Critical dimensions — sealing surfaces, mating features and wall thickness, with a stated method and gauge.
- Function — suction pull test on a defined surface, cap leak test after filling, drop test at a stated height, dishwasher cycle count for kitchen items.
- Assembly fit if the part mates with another component; a 0.3 mm drift on a press-fit becomes a returns problem.
Writing it into the purchase order
- Name the standard — ISO 2859-1, level II, with the AQL per defect class.
- Attach the specification — material, hardness with tolerance, dimensions, colour reference, packaging.
- Attach the boundary samples as photographs with the agreed limits annotated.
- Name the inspector and who pays. Third-party inspection on a first order is cheap insurance.
- Define the remedy — sort, rework, credit or remake — and the timeline for each, before anything ships.
- State who bears re-inspection cost if the first inspection fails. This one clause changes behaviour more than any other.
What to do when an inspection fails. There are three options, in order of preference. Sort the lot and ship only conforming units, with the inspector present and the reject count documented. Rework at the factory if the defect is correctable — trimming flash, re-packing — then re-inspect. Or, for a minor cosmetic miss on a non-critical programme, accept with a price concession in writing.
What you should not accept is a promise to "check more carefully next time". That is not a remedy, and the next lot will be produced by the same process that made the first one.
FAQ
Is AQL 2.5 strict enough for silicone products?
For general household goods it is a normal starting point. For anything a child may bite, tighten to critical 0 and major 1.0, and treat flash on the bite surface as critical rather than cosmetic.
Can the factory inspect its own order?
Yes, and most do — but for a first order or a new mould, use a third-party inspector. The cost is small relative to the risk of receiving 20,000 pieces with a colour problem that was obvious under daylight.
How long does a pre-shipment inspection take?
Usually one working day on site for a normal lot, plus one to two days for the report. Book it before the factory finishes packing, not after the container is loaded.
Should the AQL apply to the carton as well as the product?
Yes. Add packing checks — carton mark, quantity per carton, poly bag thickness, desiccant — to the same inspection. Packing errors cause more chargebacks in retail than moulding defects do.
Next step
Send us your current inspection checklist or the last defect report you received, and we will tell you which lines are unenforceable and what to replace them with. Our OEM and ODM process includes boundary-sample approval at T1, and you can see the part categories we mould under our product range.