Who Owns the Mould? Silicone Tooling Ownership, Amortization and Mould Transfer
Tooling is where most custom silicone programmes quietly lose money. The mould itself is a one-off cost, but the words around it — who owns it, whether the price includes it, and what happens when you want to move it — decide whether your second supplier quotation starts from a clean sheet or from a hostage negotiation.
The three ways factories price tooling
| Model | How it works | What it means for you |
|---|---|---|
| Tooling billed separately | Mould cost quoted as its own line, paid upfront, part price excludes it | Cleanest model. You own the asset, unit prices stay transparent |
| Tooling amortised into unit price | No upfront fee; the mould cost is spread across the first N pieces or orders | Easier cash flow, but the price only holds if you keep ordering; ownership is often left vague |
| "Free" tooling | No tooling line at all; cost hidden in a higher unit price | You never truly own the mould, and you pay for it again at every supplier switch |
The third model is the one that costs buyers the most over a product's life. A "free" mould is a mould the factory owns, and ownership answers the only question that matters when the relationship changes: who decides where this part is made?
What tooling actually costs, and why quotes differ
A single-cavity compression mould for a simple silicone part — a mat, a lid, a grip — typically sits in the hundreds-to-low-thousands USD range, depending on steel grade, cavity count and expected life. Multi-cavity tools, family tools that produce several parts in one shot, and LSR injection tools with cold-runner systems all move up from there. When two quotes for the same part differ sharply on tooling, the usual causes are:
- Steel grade — P20 for short runs versus hardened tool steel for hundreds of thousands of cycles. Cheap steel is the most common reason a tool starts producing flash at cycle 20,000.
- Cavity count — more cavities lower unit cost and raise tooling cost; a quote with fewer cavities is not comparable to one with more.
- Shut-off and insert complexity — undercuts, overmoulding cores and collapsible features add real engineering hours.
- Mould base quality — guiding and clamping hardware affects flash consistency for the tool's whole life.
Ask each supplier to state steel grade, cavity count and guaranteed shot life in the quotation. Those three lines make tooling quotes comparable in a way the total number never will.
The ownership clause worth insisting on
Ownership language does not need to be long. Three sentences cover it:
- The mould is the buyer's property upon payment of the tooling fee, and is tagged and stored at the supplier's cost between orders.
- The buyer may request the mould's release at any time, and the supplier will ship it within an agreed number of days after settlement of outstanding invoices.
- The supplier will not use the mould to produce for any other party without written consent.
Clause 2 is the one factories resist, and the resistance is informative. Without it, moving suppliers means either abandoning the mould — paying twice — or negotiating its release from a position of weakness. With it, the mould moves by freight, takes a few days, and your new supplier's first article report tells you whether it was maintained.
Amortised tooling: the fine print that bites
Amortisation is a legitimate structure, especially for startups managing cash. Read two things before accepting it. First, what happens to the mould once it is "paid off" — does ownership transfer in writing, or does the factory keep it? Second, what happens to the unit price if you stop ordering for six months? Some agreements re-amortise after an order gap, which means you pay for the same asset more than once. Both answers should be in the purchase order, not in a verbal assurance during a factory call.
Moving a mould: what the receiving factory needs
A mould transfer is routine when handled properly. The receiving supplier needs the tool itself, ideally with its last production article and any spare inserts, plus the material specification and the previously approved sample. Expect a trial run — a T0-style verification — before mass production, because every press has slightly different platen dimensions, clamping behaviour and temperature control. Budget a few days for this verification rather than assuming the tool drops in and runs. If the tool arrives worn or rusty from poor storage, the trial will reveal it, and refurbishment of a parting line is a modest, predictable cost compared with a fresh mould.
How we structure tooling with our clients
We quote tooling as a separate, itemised line: steel grade, cavity count, shot-life expectation and lead time are all written into the quotation, and the mould belongs to the client on payment. When a client moves production for commercial reasons, we release the tool with the last production sample and batch records, because a supplier who makes leaving easy is a supplier you come back to. You can see how this fits into the wider OEM and ODM development process, including mould design and first-article approval.
FAQ
Is a cheaper mould always a false economy?
For volumes above roughly 50,000 cycles, yes in most cases. Low-grade steel softens and the parting line wears into a flash generator. For a trial or a genuinely small lifetime volume, a cheaper P20 tool can be the rational choice — the decision should be made against expected total volume, not against the invoice.
Who pays for mould maintenance and repairs?
Normal maintenance is the factory's cost of doing business and should not be billed separately. Repairs caused by design changes you request are yours; repairs caused by tool wear within the promised shot life are the factory's. Put this sentence in the PO and the arguments disappear.
Can we register or mark the mould as ours?
Yes — ask for the tool to be stamped or tagged with your project code and "property of [your company]" on the mould base. It costs nothing, prevents accidental use for other clients, and makes physical verification during an audit trivial.
Next step
Send us the part drawing and expected annual volume, and we will quote tooling as an open, itemised line with steel grade, cavity count and shot life stated — plus a unit price that does not depend on you never changing suppliers. For reference parts in consumer electronics, see our silicone 3C digital accessories range, many of which run on client-owned tooling.